产品介绍
滤芯介绍 贺德克滤芯是输送介质的管道系列中不可缺少的部分，通常安装在液压系统的进口端过滤中，用来滤除流体介质中的金属颗粒、污染杂质等，可保护设备的正常工作，当流体进入过滤器后，其杂质被阻挡，而清洁的滤液则由过滤器出口排出。当需要清洗时，只要将滤芯从过滤器中取出，用工业液体处理后装入即可。贺德克滤芯产于德国贺德克(HYDAC Technology GmbH)公司。公司致力于科研开发流体过滤技术、液压控制技术、电子测量技术的元件和装置，是世界著名的过滤器、蓄能器、液压阀、电子产品、管夹、电磁铁、液压系统总成等产品的液压件的制造。进口液压滤芯的典范
滤芯特点
1.该滤芯采用美国进口玻纤/不锈钢网制成，具有排污方便、流通面积大、压力损失小，结构简单，体积小，重量轻、过滤材质均匀等。
2.滤材的兼容性适用于一般液压油的过滤。
3滤芯由两侧的固体滤料和稳定性较强的过滤材料做支撑，.符合ISO3724/76液压滤芯流动疲劳特性的验证。
Products
Introduction filter HYDAC filter is an indispensable part of the pipeline transport medium series, usually installed in the inlet end of the hydraulic system filter is used to filter out the metal particles in the fluid medium, contaminants can protect normal work when the fluid enters the filter, the impurity is blocked, and clean filtrate from the filter outlet. When cleaning is required, as long as the cartridge is removed from the filter, can into industrial liquid handling. HYDAC filter produced in Germany HYDAC (HYDAC Technology GmbH). The company is committed to the research and development of fluid filtration technology, hydraulic control technology, electronic components and devices of measurement techniques, is a world-famous filter, accumulator, hydraulic valves, electronic products, pipe clamps, solenoid, hydraulic system assembly, and other products hydraulic parts manufacturing. The imported hydraulic filters model
Filter characteristics
The filter is made of imported fiberglass / stainless steel mesh, with convenient sewage flow area, the pressure loss is small, simple structure, small size, light weight, and uniform filter material.
The compatibility of the medium suitable for general hydraulic oil filter.
3 do support the filter element from the the strong filter material of the filter and stability of both solid. Meet ISO3724/76 hydraulic filters verification of flow fatigue characteristics.
滤芯清洗方式
每6 个月一次, 取出滤芯进行清洗。
Once every six Remove filter cleaning.
清洗可采用压缩空气或者高压蒸汽(最高温度不得超过
80 0C),
Use compressed air or high pressure steam cleaning
(the maximum temperature of over 80 0C).
在滤芯外侧40 厘米距离处进行喷洗。从滤芯顶部慢慢
移向底部。
In the filter lateral distance of 40 cm for jet washing.
Gradually shift from the top of the bottom of the filter.
清洗结束后, 将滤芯开口朝下以便水份流出。
After washing, opening facing down so that water will
filter out.
室温下放置约一周待其晾干。
Once dry place at room temperature for about a week.
或者在烘箱内(最高温度不得超过80 0C)烘大约20 小时
可干。
Or in the oven (the maximum temperature of over 80
0C) to try to be out of work for about 20 hours.
三、. 维护Maintenance
每 3 个月一次, 检查除尘器内部的洁净部位
是否有粉尘出现;
如果出现粉尘, 则:
1. 检查滤芯是否破损;
2. 检查密封部位;
3. 检查滤芯是否正确安装在安装板上。
Once every three months to check
whether a dust precipitator internal
parts of the cleanliness there.
If dust :
1. Check whether the damaged filter;
2. Seal inspection sites;
3. Check whether the correct installation of
the filter installed board.
